View BA6458_102823.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Motor driver ICs
3-phase motor driver
BA6458FP-Y
The BA6458FP-Y is an one-chip IC designed for driving video cassette recorder cylinder motors. It is a high-performance IC with a 3-phase, full-wave, pseudo-linear drive system. The IC is compactly packaged. FApplications Video cassette recorder cylinder motors FFeatures 1) 3-phase, full-wave, pseudo-linear drive system. 2) Output saturation voltage is low with low variation. 3) Built-in torque limit pin. FBlock diagram
4) Contains two amplifiers and two hysteresis amplifiers to amplify FG and PG signals. 5) Built-in thermal shutdown circuit.
603
Motor driver ICs
FAbsolute maximum ratings (Ta=25_C)
BA6458FP-Y
FRecommended operating conditions (Ta=25_C)
FPin descriptions
604
Motor driver ICs
FElectrical characteristics (unless otherwise noted, Ta=25_C, VCC=5V, VM=12V)
BA6458FP-Y
605
Motor driver ICs
FCircuit operation (1) The 3-phase Hall signal is amplified in the hall amplifiers and sent to the matrix section, where the signal is further amplified and combined. After the signal is converted to a current in the amplitude control circuit, the current is supplied to the output driver, which then provides a motor drive current. The phases of the Hall input signal, output voltage, and output current are shown in Fig. 1.
BA6458FP-Y
(2) Torque control pin The output current can be controlled by adjusting the voltage applied to the torque control pin (pin 9).
(3) Start / stop pin The motor is in the run mode when the pin input voltage is 3.5V or more and in the idle mode (all output transistors are off) when the voltage is 1.2V or less. (4) Power ground pin (RNF pin) The RNF pin is the output stage ground pin. Connect a resistor (0.5 recommended) between this pin and the ground to monitor the output current. (5) Torque limit pin (TL pin) The output current can be limited by applying a voltage to the torque limit pin. Control is provided so that this pin will have the same potential as the RNF pin. Note that there is an offset in the TL-pin voltage. (6) Phase compensation pin (CNF pin) Connect a capacitor between this pin and VCC if the output tends to oscillate. (7) Amplifiers 1 and 2 Amplifiers 1 and 2 have an open loop gain of about 70dB (typical). The input terminals are biased internally to 2.45V (typical). (8) Hysteresis amplifiers The hysteresis amplifiers have a hysteresis width of 120mV (typical). The input terminals are biased internally.
606
Motor driver ICs
FOperation notes (1) Input / output circuit (1) Start / stop switching pin (25 pin)
BA6458FP-Y
(4) Driver output (A1: 24 pin, A2: 22 pin, A3: 21 pin)
(2) Torque limit pin (18 pin)
(5) Hall input (H1+: 1 pin, H1*: 2 pin, H2+: 3 pin, H2: 4 pin, H3+: 5 pin, H3*: 6 pin)
(3) Torque control input (9 pin)
(6) I / O of amplifiers 1 and 2
607
Motor driver ICs
(7) I / O of hysteresis amplifiers
BA6458FP-Y
Note that resistance values of the I / O circuits can vary 30% (2) Torque control The RNF-pin output voltage is plotted against the torque control input voltage (EC) in Fig. 10.
(5) Torque limit pin (pin 18) The output current can be limited by applying a voltage to the torque limit pin. Control is provided so that this pin will have the same potential as the power ground pin. Note that there is a voltage offset on this pin. The RNF-pin voltage is 0.325V when the TL-pin voltage is 0.4V (typical) and the RNF-pin resistance is 0.5. Note that the voltage offset changes with the RNF-pin resistance. (6) Amplifiers 1 and 2 Unpredictable outputs may occur when the amplifier input is outside the recommended range. (7) Hysteresis amplifier An input range of 0.6V to (VCC X 1.2V) is recommended. Unpredictable outputs may occur when the input is outside this range. (8) Thermal shutdown circuit (TSD) The circuit puts the driver outputs (A1, A2, and A3) to the open state at the temperature of 175_C (typical). There is a temperature difference of about 20_C between the temperatures at which the circuit is activated and deactivated.
(3) Start / stop pin The I / O equivalent circuit of the start / stop pin is shown in (1). 1) of "Precautions for use." The pin has a temperature dependence of *7mV / _C, and the resistance can vary 30%. Take the temperature effect into consideration when designing your application. (4) Hall input The I / O equivalent circuit of the Hall input pins is shown in (1). 5) of "Precautions for use." The Hall devices can be connected in either series or parallel.
608
Motor driver ICs
FApplication example
BA6458FP-Y
609
Motor driver ICs
FElectrical characteristic curves
BA6458FP-Y
FExternal dimensions (Units: mm)
610

▲Up To Search▲

Price & Availability of BA6458

	To Download BA6458 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .